Improving Your Property - Helping you improve your property

Lining paper, what is it? :: Posted by: Admin on February 4th, 2015

Lining paper, what is it?

Lining paper has been traditionally used to produce a good, sound, smooth surface for wallpapering over, however it is now more popular to hang lining paper and emulsion over it.

Lining paper is used to remove any small imperfections on a wall or ceiling, it is not however a miracle cure, so preparation should always be done before hanging lining paper. It isn’t a substitute for plastering either.

Once all the holes and cracks have been filled, the walls or ceiling should be properly rubbed down and any filler should be sanded smooth and level. One this is done dust down the walls to remove any loose debris. You can seal any filler by either using a ‘size’ such as watered down wallpaper paste, or you can emulsion over the filler to help seal it off.

Lining paper rolls

What thickness lining paper

Lining paper comes in different thicknesses, guages or grades, this refers to their weight. they start at 800 guage and go up to 2000 guage, it all depends on how thick you want it to be. Lining paper does offer some insulation qualities but there are also specialist papers for this.

A good mid-range lining paper to go for is 1200 or 1400 guage, they aren’t too thin and not to thick to be hard to work with.

Can I paint lining paper

As mentioned above, lining paper is meant to produce a smooth background for wallpapering over, but yes you can paint over the lining paper once it is fully dried.

Cross lining, what’s that?

Cross-lining is where the lining paper is hung horizontally rather the vertically like traditional wallpapers, normally if you are going to be emulsioning over the lining paper you could hang it as you would wallpaper, vertically.

Once you have hung the lining paper you need to allow it to fully dry before you emulsion over it, this will take normally between 12 – 24 hours depending on drying conditions.

How to measure for lining paper

Before you buy lining paper or order wallpaper you need to know how much to buy, I have written an article on how to measure a room for wallpaper that explains how you need to do it. I have also written a wallpaper calculator so you can work out how many rolls of wallpaper you need to buy.

Cost of lining paper

With everyone having to tighten their belts these days, cost is a real factor when it comes to decorating, wallpaper can be very expensive if you plan to wallpaper the entire room, a way around this is to only do one wall, or a feature wall as it is known.
If however you wish to change the look of a room every couple of years, or you have pets or children that makes wallpaper not a viable option, lining paper and emulsion maybe the answer.

Once lining paper has been put up it can painted over and over again, saving costs in the long run as all that is required is a fresh new coat of emulsion. Also, if you then decide to wallpaper at a later date, you can do so over the emulsioned lining paper.

Tags: , , , , ,
Posted in Building, Decorating, DIY Tips, Handyman tips | No Comments »


DIY jobs – The right tool for the job :: Posted by: Admin on July 22nd, 2014

Hammer and screw

DIY jobs – The right tool for the job

When it comes to tackling DIY jobs it is best to be planned and prepared, whether it be a building job, gardening, a simple handyman job, plumbing or woodworking job, it is best to be prepared with the correct tools. By using the wrong tool for the job you run the risk of personal injury, damaging equipment or the job you are working on, and more often than not using the wrong tool makes the job harder to do and makes the job take longer to complete.

The right tools for the job

It maybe an old saying and a bit of a cliche but, by having the right tool for the job, will make the job far easier, safer and produce a far superior job. Rather than struggling without the correct tools and in an unsafe way and finishing up with a botched job that you’ll more than likely end having to redo, or calling in a professional to do the job properly for you.

A clean workspace is a safe workspace

If you have a clean environment to work in, without clutter and dangerous hazards such as extension leads and tools all over the floor, the DIY job will be a far safer place to work and a easier place to work, so you will enjoy doing some DIY rather than hate it and shudder at the thought of any DIY tasks. It doesn’t take long to move stuff out of the way and tidy up.

Be prepared

Take time to think about the job, gather the tools you will need, remove any dangers (this includes small children and pets) from your work area. Think about how you are going to do the job, have you got everything that you require to complete the job, the last thing you want to do is have to rush out and buy something in the middle of the job.

If you are doing a plumbing job don’t forget to turn off any water supply before removing taps or cutting pipes. Make sure electrical supplies are turned off before touching wires or removing socket face plates.

Gardening

If you decide to do a DIY job in the garden you should still think about the right tool for the job, and of course safety, such as using an extension lead with a RCD plug (residual-current device) so that if you run over it with the mover the power will be cut immediately.

Power tools

Lets face it we all love power tools, right? Well in the wrong hands they can cause serious injury and damage. However, having the correct power tool for the job will again make life easier, quicker and far more enjoyable.
Wallpaper and heat gun

Your stories

If you have any stories you would like to share, please do so in the comment box below. We would love to hear them,

Tags: , , , , , ,
Posted in Building, Decorating, DIY Tips, Gardening, Handyman tips, Plumbing, Woodwork | No Comments »


Filling holes in wood with wooden plugs :: Posted by: Admin on March 26th, 2014

wooden plug cutter

Filling holes in wood with wooden plugs

When it comes to filling holes in wood, plaster etc it is typically done with a powder filler or a two part filler, as discussed in this blog post about fillers, the different types and their uses.

But what do you do if you want to fill screw holes in wood and then varnish the wood in clear varnish or leave it natural, you could use a natural coloured filler or you could use wooden plugs or pellets. This may occur, for example if you have a hardwood window sill, such as oak or mahogany and you want to use a clear varnish on it, then you don’t want to see the filler, this is where these wooden plugs come in.

What are wooden plugs

Wooden plugs are used to conceal and hide screw holes in wood without the use of a wood filler. They are made from the same wood as surrounding wood so that the grain and wood colouring match in when finished. You can make your own wooden plugs by buying a wooden plug cutter, these are available from any good hardware or timber store. They come in different sizes to match the size hole you wish to fill.

When you drill the plug you will notice the edges are slightly tapered, this is to allow for a good fit.

Using wooden plugs

Firstly you will require a piece of wood, such as an off cut of the timber you wish to fill the screw hole in. You will also need the plug cutter.
Lay the off cut on a flat surface, drill into the off cut with the plug cutter, this will produce a plug for you. Once you have the plugs you require you can fix them into place.
Take some wood glue and put a little around the plug and a little in the screw hole. Next place the plug into the hole making sure the grain of the plug runs the same way as the surrounding wood, give the top of the plug a little tap with a hammer to ensure a good tight and secure fit. Wipe any excess glue that may ooze out with a damp cloth, allow the glue to fully dry.
When the glue has fully dried you can finish the plug off, to do this you need to carefully remove the top of the plug with a sharp chisel, leave the plug just proud of the surrounding timber. The remaining plug can then be sanded down level with the surrounding area.

Once you are happy with the plug you can apply the finishing coat over the wood and the screw hole will almost be invisible.

Wood plugs

Tags: , , , , , , , ,
Posted in Building, Decorating, DIY Tips, Handyman tips, Woodwork | No Comments »


Boxing in pipework :: Posted by: Admin on January 13th, 2014

Boxing in pipework

Boxing in pipework

Pipes such as heating pipes or waste pipes can look ugly and can be a dust trap, they can be hard to clean and even paint around. The ideal solution is to box pipework in, once they are boxed in, the box can be decorated the same as the surrounding area, such as tiled or painted.

Typically to box in pipework you use timber battens and plywood or MDF, the battens are normally 2×1 inches (50×25 mm) or 2×2 (50×50 mm). The plywood or MDF can be 6 or 9 mm. All of the materials used will depend on the circumstances you plan to box the pipes in. You may even wish to use plasterboard and plaster the box.

Tools required for this job

  • Battens (2×1 or 2×2) (50×25 mm or 50×50 mm)
  • Drill
  • Drill bits
  • Screw or panel pins
  • Spirit level
  • Screwdriver / drill with screwdriver bit
  • Hammer
  • Plywood, MDF, Plasterboard
  • A pencil
  • Tape measure

How to box in pipes

Take the battens and hold them against the wall, use a spirit level to ensure they are upright and level, next drill holes through the wood into the wall, use rawl plugs and screws to fit the batten to the wall ensuring they are level.

Once the two wall battens are fixed you can cut the plywood to the correct size, fix a batten on the outside corner of one of the pieces of plywood, this will allow you to screw the other length of plywood to it giving the external corner a good strong fixing.

Decorating the box

Once the boxing in is done you can decorate the box, if you are painting the box, fill the screw holes and rub them down then apply the appropriate paint to match the surrounding area, you may have to prime the box first to seal the plywood. If you are tiling the boxing in, cut and fix the tiles to match in with to other tiles. You can add skirting boards to horizontal boxing in to match the room, and coving to vertical boxing in to make the box become part of the room and once decorated should like it has always been there.

Horizontal and vertical pipes

The same method for boxing in applies if you are boxing in horizontal or vertical pipes.

You can box in heating pipes, hot and cold water pipes, soil pipes and waste pipes to tidy them up and make them look part of the room.

Tags: , , , , , , , , ,
Posted in Building, Decorating, DIY Tips, Handyman tips, Plumbing, Woodwork | No Comments »


Top

My Paintbrush logo

Copyright © 2012 - 2017 Adrian Rayfield. All Rights Reserved.
This blog is protected via Copyscape Protected by Copyscape Online Infringement Checker Please do NOT infringe our copyright.
Entries (RSS) and Comments (RSS).
We currently have: 35 posts :: We also have 49 comments, why not have your say?

Admin - Log in